Water Level Meter WM-30

Features and Benefits - This water leveling tool features a flexible tape/cable for easy winding and unwinding, even in cold temperatures. Its waterproof design ensures durability in various conditions. The tool includes permanent depth markings with extra tubing protection for enhanced reliability. A strong 80lb base magnet allows it to be placed at any angle on metal sections of boreholes, wells, or standpipes. Equipped with 3 bright LED signals, visibility is guaranteed from any angle, even in bright sunlight, up to 40 ft. Powered by (2) 9-volt batteries, this water leveling tool provides maximum usage between battery changes. Its lightweight, pocket-sized, and portable design is ergonomically crafted for ease of use. The probe can be quickly and easily attached to the magnetic base when not in use or can hang from the handle prior to use. The magnetic base allows for fast access, as it can be fastened to the metal panel of a work van or any metal surface. An On/Off switch conserves battery life, while a power drill nut driver attachment can be utilized to speed up the winding and unwinding of the tape/cable, preventing fatigue. 

Operation: The water leveling tool can be used at any angle and easily attaches to any well, borehole, or standpipe with a metal surface. Each unit consists of a metal probe fitted to a flexible cable wire tape, wound onto a hand-held reel with an ergonomic handle. The cable connects to an electronic circuit, 3 LED signal indicators, and (2) 9-volt batteries, complete with an On/Off switch. The sensor probe features an insulated gap that acts as a switch, completing the circuit upon contact with water. The cable includes a non-stretch flexible wire/tape with copper conductors marked in 4” intervals or 10cm intervals, depending on the unit. For precise measurements, the ruler on the unit or the provided metal ruler can be used. The probe is lowered into the borehole, standpipe, or well. Caution: keep the cable wire away from sharp edges. The probe can be lowered by hand or with the drill attachment. Upon contact with water, the 3 LEDs illuminate, allowing a reading to be taken from the measuring cable at the port level to record the depth. Ensure the unit is turned off afterward to conserve battery life. To measure depth to the closest ½”, use the cap's ½” notched lines as a guide, placing the wire along the rubber sides and counting notches. For example, 2 notches equal 1” and 6 notches equal 3”. The distance between LEDs along the rubber sides is 4” (8 notches). Use the ruler markings on the magnetic base or the provided ruler for added accuracy once the closest footage distance is noted. Wind the water level meter cable manually by hand or with a drill. 

Specifications: Power Supply: 2 x 9 Volt Batteries (included). Measuring Cable/Wire: Flex Silicone with Copper. Button: On/Off Button. Visual Indicators: 3 LED's. Magnetic Base: 80 lb Holding Capacity. Operating Environment: Rated for outdoor use and is waterproof. Battery Life: 1000+ readings, 20 hours of LEDs staying on. Operating Temperature: -40°C to 55°C (-40°F to 130°F). Response time: <100 milliseconds. Accessories: Carry Bag, Drill attachment (nut driver), Wig-nut (handle replacement when using a drill), Ball Handle (available only on 60M, 80M, 200ft & 250ft units). Markings: every 4” for ft, 10cm for Meter (use included rulers for more accuracy). Probe Diameter: approx. 20mm. WM-30: 2.3lbs, 3.8”x3.8”x7.9” 30ft length, WM-50 2.5lbs, 3.8”x3.8”x8.4” 50ft length, WM-100: 2.9lbs, 3.8”x3.8”x9” 100ft length, WM-200: 3.7lbs, 3.8”x3.8”x9.8” 200ft length, WM-10M: 2.4lbs, 3.8”x3.8”x7.9” 10M length, WM-20M: 2.6lbs, 3.8”x3.8”x8.4” 20M length, WM-30M: 3.0lbs, 3.8”x3.8”x9” 30M length, WM-60M: 3.8lbs, 3.8”x3.8”x9.8” 60M length.